Managing A Cisco Internetwork MCQ

Test your knowledge with important Managing A Cisco Internetwork MCQ and their applications. These MCQs are beneficial for competitive exams too. Explore 30 + more Managing A Cisco Internetwork MCQs at Bissoy

• A network administrator wants to upgrade the IOS of a router without removing the image currently installed. What command will display the amount of memory consumed by the current IOS image and indicate whether there is enough room available to hold both the current and new images?
  ক

  <code class="args"><em>show version</em></code>

  খ

  <code class="args"><em>show flash</em></code>

  গ

  <code class="args"><em>show memory</em></code>

  ঘ

  <code class="args"><em>show buffers</em></code>
• Which command will show you the IOS version running on your router?
  ক

  <code class="args"><em>sh IOS</em></code>

  খ

  <code class="args"><em>sh flash</em></code>

  গ

  <code class="args"><em>sh version</em></code>

  ঘ

  <code class="args"><em>sh running-config</em></code>
• You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?
  ক

  You didn

  খ

  NVRAM is corrupted.

  গ

  The configuration register setting is incorrect.

  ঘ

  The newly upgraded IOS is not compatible with the hardware of the router.
• What does the command <code class="args"><em>o/r 0x2142</em></code> provide?
  ক

  It is used to restart the router.

  খ

  It is used to bypass the configuration in NVRAM.

  গ

  It is used to enter ROM Monitor mode.

  ঘ

  It is used to view the lost password.
• You telnet into a remote device and type <code class="args"><em>debug ip rip</em></code>, but no output from the <code class="args"><em>debug</em></code> command is seen. What could the problem be?
  ক

  You must type the <code class="args"><em>show ip rip</em></code> command first.

  খ

  IP addressing on the network is incorrect.

  গ

  You must use the <code class="args"><em>terminal monitor</em></code> command.

  ঘ

  Debug output is sent only to the console.
• What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?
  ক

  <code class="args"><em>0x2100</em></code>

  খ

  <code class="args"><em>0x2101</em></code>

  গ

  <code class="args"><em>0x2102</em></code>

  ঘ

  <code class="args"><em>0x2142</em></code>
• Which command displays the configuration register setting?
  ক

  <code class="args"><em>show ip route</em></code>

  খ

  <code class="args"><em>show boot version</em></code>

  গ

  <code class="args"><em>show version</em></code>

  ঘ

  <code class="args"><em>show flash</em></code>
• You telnet to a router and make your necessary changes; now you want to end the Telnet session. What command do you type in?
  ক

  <code class="args"><em>close</em></code>

  খ

  <code class="args"><em>disable</em></code>

  গ

  <code class="args"><em>disconnect</em></code>

  ঘ

  <code class="args"><em>exit</em></code>
• The configuration register setting of 0x2102 provides what function to a router?
  ক

  Tells the router to boot into ROM monitor mode

  খ

  Provides password recovery

  গ

  Tells the router to look in NVRAM for the boot sequence

  ঘ

  Boots the IOS from a TFTP server
• Which command loads a new version of the Cisco IOS into a router?
  ক

  <code class="args"><em>copy flash ftp</em></code>

  খ

  <code class="args"><em>copy ftp flash</em></code>

  গ

  <code class="args"><em>copy flash tftp</em></code>

  ঘ

  <code class="args"><em>copy tftp flash</em></code>
• Which command will copy the IOS to a backup host on your network?
  ক

  <code class="args"><em>transfer IOS to 172.16.10.1</em></code>

  খ

  <code class="args"><em>copy run start</em></code>

  গ

  <code class="args"><em>copy start tftp</em></code>

  ঘ

  <code class="args"><em>copy flash tftp</em></code>
• Which three commands can be used to check LAN connectivity problems on a router?<br>1. <code class="args"><em>show interfaces</em></code><br>2. <code class="args"><em>show ip route</em></code><br>3. <code class="args"><em>tracert</em></code><br>4. <code class="args"><em>ping</em></code><br>5. <code class="args"><em>dns lookups</em></code>
  ক

  1 ,2 and 4

  খ

  2 and 5

  গ

  3 and 5

  ঘ

  None of the above
• You are unsuccessful in telnetting into a remote device. What could the problem be?<br>1. IP addresses are incorrect.<br>2. Access control list is filtering Telnet.<br>3. There is a defective serial cable.<br>4. The VTY password is missing.
  ক

  1 only

  খ

  3 only

  গ

  2 and 4 only

  ঘ

  All of the above
• What information is displayed by the <code class="args"><em>show hosts</em></code> command?<br>1. Temporary DNS entries<br>2. The names of the routers created using the <code class="args"><em>hostname</em></code> command<br>3. The IP addresses of workstations allowed to access the router<br>4. Permanent name-to-address mappings created using the <code class="args"><em>ip host</em></code> command<br>5. The length of time a host has been connected to the router via Telnet
  ক

  1, 2 and 3

  খ

  1 and 4

  গ

  3, 4, and 5

  ঘ

  All of the above
• You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the <code class="args"><em>copy flash tftp</em></code> command to be successful?<br>1. TFTP server software must be running on the router.<br>2. TFTP server software must be running on your laptop.<br>3. The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable.<br>4. The laptop must be on the same subnet as the router's Ethernet interface.<br>5. The <code class="args"><em>copy flash tftp</em></code> command must be supplied the IP address of the laptop.
  ক

  1, 3 and 4

  খ

  2, 4 and 5

  গ

  3 and 5 only

  ঘ

  5 only