If a product requires 10mins for production. where rating of operation is 80% and allowance is 10% then what is the SMV of this product?

রেওয়ামিলে দেনাদার ৫২,০০০ টাকা, লিখিত অনাদারি পাওনা ২,০০০ টাকা এবং অলিখিত অন্যদায়ি পাওনা ২,০০০ টাকা। যদি দেনাদারের ওপর ৫% সঞ্চিতি রাখা হয় এবং অনাদায়ি পাওনা সঞ্চিতির ক্রেডিট ব্যালেন্স ১,০০০ টাকা হয়, তাহলে চলতি বছরে অন্যনায়ি পাওনা সঞ্চিতি কত রাখতে হবে? (In trial balance, account receivable is of Tk. 52,000 recorded bad debt of Tk.2,000 and unrecorded bad debt of Tk. 2,000. What is the amount of allowance for doubtful accounts kept in current year if the allowance is 5% on accounts receivable and credit balance in allowance for doubtful accounts currently is of Tk. 1,000 )

A

২,৫০০ টাকা (Tk. 2,500)

B

১,০০০ টাকা (Tk. 1,000)

C

২,৪০০ টাকা (Tk. 2,400)

D

1,500 টাকা (Tk. 1,500)

In this method of underwriting, the underwriter gives rating points for all the negative or adverse factors, totals them and decides extra mortality rating. Which method are we talking about?

A

Biometric rating

B

Judgmental rating

C

Clinical rating

D

Numerical rating

Type of rating to which all credit rating agencies does not consider is classified as

A

split rating

B

sinking rating

C

automated rating

D

floating rating

For the same a.c. power output as above, what should be the minimum power rating of transistor for class B operation?

A

10 W

B

4 W

C

8 W

D

None of the above

Scheme-1: C6H5N2Cl→CuCNC6H5CN→H2o/H+C6H5COOH→∆Product-I Scheme-2: C6H5NO2→Fe/HCLC6H5NH2→N2NO3+HCL, 273KC6H5N2Cl→H2O/H+Product-II Scheme-3: CH3COOH→NH3CH3CONH2→NaOBrProduct-III উল্লিখিত Scheme সমূহে Product-I, Product-II এবং Product-III হলো যথাক্রমেঃ

A

C6H5COONH4, C6H5Cl and CH3OH

B

C6H5CONH2, C6H5NH2 and CH3OH

C

C6H5CONH2, C6H5NH2 and CH3NH2

D

C6H5CONH2, C6H5OH and CH3OH

If Sabbir requires 5 minutes to make a box and Zoha requires 7 minutes to make a box, what will be the number of boxes made by Sabbir to the number of boxes made by Zoha if they work for 5 hours and 50 minutes?

A

5 to 6

B

7 to 5

C

5 to 7

D

6 to 5

If an aluminium pattern made from a wooden master pattern is to be used for grey iron castings, then the shrinkage allowance allowed on the wooden pattern should be

A

10 mm/m

B

16 mm/m

C

20 mm/m

D

26 mm/m

In case of a shell and tube heat exchanger, the minimum shell thickness for carbon steel (inclusive of corrosion allowance) depends on shell diameter and is in the range of __________ mm.

A

3-5

B

5-11

C

8-15

D

12-18

Samit was given some money to take care of his travel during a 6-day sales drive he had to undertake. However, he had to increase his stay by another 4 days and as a result his average daily travel allowance went down by Rs. 56. What was the amount that was sanctioned to him in the beginning?

A

Rs.336

B

Rs.560

C

Rs.840

D

Rs.420

In the design of a shell and tube heat exchanger, the corrosion allowance

A

Need not be provided for non-pressure parts like tie rods, spacers, baffles, supports etc

B

For carbon steel and cast iron pressure parts is 1.5 mm (except for tubes) and for severe conditions it is 3 mm

C

For internal cover and tube sheet is provided on both the sides

D

All of the above

If a product requires 10mins for production. where rating of operation is 80% and allowance is 10% then what is the SMV of this product?

Related Questions