Bissoy.com
Doctors Medicines MCQs Q&A

In a shell and tube heat exchanger for a given heat transfer surface area, smaller diameter tubes are favoured as compared to larger diameter ones ; because the smaller diameter tubes

In a shell and tube heat exchanger for a given heat transfer surface area, smaller diameter tubes are favoured as compared to larger diameter ones ; because the smaller diameter tubes Correct Answer Can be fitted into a smaller shell diameter hence the cost of the heat exchanger would be less

Related Questions

A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
Plate type heat exchangers have less surface area as compared to a similar Shell and Tube heat exchanger. A Shell and Tube Heat Exchanger of equivalent area weigh six-seven times less than a Plate Type heat exchanger.
In a survey related to United Nation Security Council, 58% of those asked were in favour of at least one of the proposals I, II and III. 60% of those asked favoured proposal I, 25% of them favoured proposal II, and 15% of them favoured proposal III. If 4% of them favoured all three proposals, then what percentage of those asked favoured more than one of the three proposals?
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is
Which of the following statements about Printed circuit heat exchanger are correct? Statement 1: Printed circuit heat exchanger is an example for direct heat exchanger. Statement 2: It has high heat transfer surface area per unit volume of the exchanger.
In a counter flow heat exchanger, water flowing through a tube of 10 cm inner diameter is heated by steam condensing on the outside of the tube. The convective film coefficient on the water and steam side are estimated to be 12000 and 20000 k J/m2 hr degree. Neglecting tube thickness and its resistance to heat flow, workout the overall heat transfer coefficient for the heat exchanger
The important design and operating considerations for Extended-Surface Compact Heat Exchangers are: (1) Both fluids may have high or low heat transfer coefficients (2) As the tubes are very narrow (low DH), the fluid used should not be corrosive as effective cleaning of tubes is not possible. (3) The fluid pressure drop calculation is important as a regulatory method to ensure long life of the tubes. (4) Unlike shell and tube type heat exchangers, these are limited when it comes to operating pressure and temperature.