A spherical porous catalyst particle of radius R is subjected to reactant A which reacts to form B by a zero order surface reaction A → B. Film mass transfer resistance is negligible and pore diffusion of A is rate controlling. The effectiveness factor of the catalyst is reported as $$\frac{7}{8}$$. Which of the following statement is true?

A spherical porous catalyst particle of radius R is subjected to reactant A which reacts to form B by a zero order surface reaction A → B. Film mass transfer resistance is negligible and pore diffusion of A is rate controlling. The effectiveness factor of the catalyst is reported as $$\frac{7}{8}$$. Which of the following statement is true? Correct Answer Inner catalyst core of radius $$\frac{{\text{R}}}{8}$$ does not participate in reaction

Bissoy MCQ

Related Questions

Effectiveness factor (E) of a catalyst pellet is defined as, E = (actual rate within pore of catalyst/rate if notsnowed by pore diffusion) Effectiveness factor for a first order reaction is given by (where, T = Thiele modulus)
For a first order isothermal chemical reaction in a porous catalyst, the effectiveness factor is 0.3. The effectiveness factor will increase if the
For the reaction, A = X + Y, the respective concentrations are CA, CX and CY. The forward reaction rate constant is kf and the backward reaction rate constant is kb. Choose the correct statement from the following:
P. At equilibrium, kf CA > kB CxCy
Q. If the reaction is irreversible than, kb CXCY = 0
R. The backward reaction rate will essentially be first order, if the forward reaction rate is first order.
S. Activation energy for the first order forward reaction will be independent of temperature.
A solid-oxide fuel cell is fed with carbon monoxide and reacts with air to produce CO2. This reaction will produce 2 electrons which are used to power an electric circuit external to the fuel cell. The reaction equation is shown below: 2CO(g) + O2(g) -> 2CO2(g) ΔHr° = -565.96 kJ/mol This reaction does not occur for other types of fuel cells which use a catalyst, such as polymerelectrolyte membrane or phosphoric-acid fuel cells. The presence of carbon monoxide on the anode side of these types of fuel cells will cause catalyst poisoning, reducing the efficiency and voltage of the fuel cell. Determine the rate of enthalpy change for a carbon dioxide production rate of 208 mol/hr. The extent of the reaction occurring in the fuel cell can be obtained by the following equation: where:
Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants ; but it is a function of reaction temperature. In a chemical reaction, the time required to reduce the concentration of reactant from 100 gm moles/litre to 50 gm moles/litre is same as that required to reduce it from 2 gm moles/litre to 1 gm mole/litre in the same volume. Then the order of this reaction is
If Thiele modulus is __________ , then the pore diffusion resistance in a catalyst may be considered as negligible.
A finned surface consists of root or base area of 1m2 and fin surface area of 2m2. The average heat transfer coefficient for finned surface is 20W/m2K effectiveness of fins provided is 0.75. If finned surface with surface with root or base temperature of 50°C is transferring heat to fluid of 30°C, then the rate of heat transfer without using fin is _______
The configurations of the reactant and the product in the following reaction, are
Basics of Organic Reaction Mechanism mcq question image
Consider the following statements regarding the importance of diffusion and choose the correct answer:
1. The exchange of gases takes place by the principle of dependent diffusion
2. The process of diffusion is involved in transpiration of water vapours
3. The ions are absorbed by the simple diffusion during passive salt uptake
4. Diffusion is an effective means of transport of substances over a very short distance and helps in the translocation of food materials
For a first order chemical reaction in a porous catalyst, the Thiele modulus is 10. The effectiveness factor is approximately equal to