A device used for lifting or lowering objects suspended from a hook at the end of retractable chains or cable is called

A device used for lifting or lowering objects suspended from a hook at the end of retractable chains or cable is called Correct Answer Hoist

A device used for lifting or lowering objects suspended from a hook at the end of retractable chains or cable is called Hoist
Bissoy MCQ

Related Questions

S1: Instantly the full load yanked Gordy towards the side of the bridge.
P: But the pull of the cable was too much.
Q: He could hardly feel the cable, slipping through his fingers, ripping off his gloves, and streaking over the railing like an escaping snake.
R: It smashed his hands hard against the top of the railing, causing a split - second feeling of fierce pain followed by numbness.
S: He held on to the cable; it had been hard work lifting it, and he did not want to have to start over again.
S6: Feeling a sharp burning sensation where the cable was speeding between his things, Gordy rose on tiptoe and as he did, the slithering coil of cable tightened around his left foot and yanked him over the railing.

The Proper sequence should be:
Study the following statements and mark your answers:
Wage Incentive Plans have the following objects:
I. Increasing worker's morale
II. Lowering unit cost
III. Lowering capital cost
IV. Lowering depreciation charges
Read the following and mark your answer. Wage incentive plans have the following objects
1. Increasing workers morale
2. Lowering unit cost
3. Lowering capital cost
4. Lowering depreciation charges
When device A has a cable that plugs into device B, and device B has a cable that plugs into device C and device C plugs into a port on the computer, this arrangement is called a _________
A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?

Subnetting mcq question image

1. A crossover cable should be used in place of the straight-through cable.
2. A rollover cable should be used in place of the straight-through cable.
3. The subnet masks should be set to 255.255.255.192.
4. A default gateway needs to be set on each host.
5. The subnet masks should be set to 255.255.255.0.
You are setting up a network in a school. You need to network 5 computers for the file and printer sharing. You want to use some donated cable and Ethernet adapters. You identify the donated adapters as ARCnet coaxial network adapters and 10Base2 Ethernet network adapters. You install an Ethernet adapter in each of the 5 computers and connect the donated cable. The computers are NOT able to maintain reliable communication. You suspect that you are NOT using the correct type of coaxial cable. Which type of coaxial cable should you be using?
You have been given the task of installing cables for an Ethernet network in your office. The building is an older one, and-you have limited work space. In addition, the network cable will have to share the existing conduit with telephone cable, and cable segments will be up to 135 meters in length. Which cable is best suited to this installation?
A man used to rob the computers and He is active only for quarter of a year. He robs three computers Vayu, Tejas and Agni. January was unfortunate month for Tejas. Vayu was stolen in March. Now he used three tools Pliers, Screwdriver and Hook to rob all the parts from the computer and Make His own computer. He Rob Monitor from Tejas but Does not use hook. He robs Printer from Vayu and Use Pliers. And from Third Computer he robs Keyboard. i) In which month was Agni stolen?ii) Which tool was used for Tejas?
Your 10Base2 Ethernet cable is 185 meters long. You are planning to extend your network by adding another 100 meters of cable. The total length of the cable will be 285 meters. The network uses NetBEUI. Which device should you use?
A post tensioned cable of beam 10m long is initially tensioned to a stress of 1000n/mm2 at one end, slope is 1 in 24 tendons curved at each end , area is 600mm2, Es is 210kn/mm2, coefficient of friction between duct and cable is 0.55, friction coefficient for wave effect is 0.0015perm. During anchorage, if there is a slip 3mm at the jacking end, calculate final force?