Related Questions

The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?
A Cyaniding
B Sheardising
C Spherodising
D None of these
For hardening alloy steels and high speed steels, they are heated to
A 1100 to 1300°C
B 1300 to 1500°C
C 500 to 600°C
D 700 to 900°C
Which is false statement about case hardening? Case hardening is done by
A Electroplating
B Cyaniding
C Induction hardening
D Nitriding
'Killed steels' are those steels
A Which are destroyed by burning
B Which after their destruction are recycled to produce fresh steel
C Which are deoxidized in the ladle with silicon and aluminium
D In which carbon is completely burnt
Steels with high carbon equivalent have poor weldability, because in these steels during welding
A Carbon and other alloying elements get oxidised from the weld pool
B Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
Ferric stainless steels compared to austenitic stainless steels
A Have lower corrosion resistance
B Are harder to fabricate
C Are less ductile and hence less suitable for cold pressing
D All of the above
There are six teachers. Out of them two are primary teachers and two are secondary teachers. They are to stand in a row, so as the primary teachers, middle teachers and secondary teachers are always in a set . The number of ways in which they can do so, is-
A 52
B 48
C 34
D None of these
The secondary voltage for a certain power transformer is twice the voltage applied to the primary. The current flowing in the secondary winding will be:
A One-half the primary current
B Same as the primary current
C Twice the primary current
D No more than 10% less than the primary current
E None of the above
একটি স্টেপ আপ ট্রান্সফরমারে, গৌণ কুণ্ডলীর পাকসংখ্যা মুখ্য কুন্ডলীর পাকসংখ্যার দ্বিগুণ। যদি মূখ্য কুন্ডলীকে কোন পরিবর্তী বিদ্যুৎ লাইনের সাথে সংযুক্ত করা হয়, তাহলে মুখ্য কুণ্ডলীর তুলনায় গৌণ কুণ্ডলীতে- (In a step up transformer, the number of turns in the secondary coil is twice to that of primary coil. If you apply an alternating current in the primary coil, then in the secondary coil compared to the primary coil-)
A তড়িৎ প্রবাহের মান দ্বিগুণ হবে (current will be doubled)
B তড়িৎ প্রবাহের মান অর্ধেক হবে (current will be halved)
C তড়িৎ বিভবের মান অর্ধেক হবে (voltage will be halved)
D তড়িৎ প্রবাহের মান সমান থাকবে (Current will remain the same)
In a hardening process, the hypo-eutectoid steel is
A Heated from 30°C to 50°C above the upper critical temperature and then cooled in still air
B Heated from 30°C to 50°C above the upper critical temperature and then cooled suddenly in a suitable cooling medium
C Heated from 30°C to 50°C above the upper critical temperature and then cooled slowly in the furnace
D Heated below or closes to the lower critical temperature and then cooled slowly

Next steps