Bissoy.com
Doctors Medicines MCQs Q&A

If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface tempeature follows __________ law.

If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface tempeature follows __________ law. Correct Answer Parabolic

Related Questions

If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface temperature follows __________ law.
A large plane wall, 40 cm thick and 8 m2 area, is heated from one side and temperature distribution at a certain time instant is approximately prescribed by the relation T = 80 – 60 x +12 x2 + 25 x3 – 20 x4 Where temperature t is in degree Celsius and the distance x in meters. Make calculations for heat energy stored in the wall in unit time. For wall material: Thermal conductivity = 6 W/m K and thermal diffusivity = 0.02 m2/hr.
Consider the following statements about thermal conductivity: 1) Thermal conductivity decreases with increasing molecular weight 2) Thermal conductivity of non-metallic liquids generally decreases with increasing temperature 3) Thermal conductivity of gases and liquids is generally smaller than that of solids Which of the above statements are correct?
The temperature variation of a thick brick wall during periodic heating or cooling follows a sinusoidal waveform. During a period of 24 hours, the surface temperature ranges from 25 degree Celsius to 75 degree Celsius. Workout the time lag of the temperature wave corresponding to a point located at 25 cm from the wall surface. Thermo-physical properties of the wall material are; thermal conductivity = 0.62 W/m K; specific heat = 450 J/kg K and density = 1620 kg/m3
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
The temperatures on the two sides of a plane wall are t1 and t2 and thermal conductivity of the wall material is prescribed by the relation K = k0 e (-x/δ) Where, k0 is constant and δ is the wall thickness. Find the relation for temperature distribution in the wall?
A plane wall of thickness δ has its surfaces maintained at temperatures T1 and T2. The wall is made of a material whose thermal conductivity varies with temperature according to the relation k = k0 T2. Find the expression to work out the steady state heat conduction through the wall?
The temperature distribution at a certain time instant through a 50 cm thick wall is prescribed by the relation T = 300 – 500 x – 100 x2 + 140 x3 Where temperature t is in degree Celsius and the distance x in meters has been measured from the hot surface. If thermal conductivity of the wall material is 20 k J/m hr degree, calculate the heat energy stored per unit area of the wall
A type I superconductor is 1. A conductor of infinite conductivity at all temperatures. 2. A conductor with a very large conductivity below a critical temperature. 3. A material showing susceptibility -1 below the critical temperature. 4. A perfect conductor having conductivity drastically reduced by a critical current.
The accompanying image shows a large cube made of dark and white small sugar cubes. Small cubes of the diagonally arranged row of the bottom surface of the large cube, small cubes of the row with one face on the right-hand surface of the large cube, small cubes of the row with one face on the front surface of the large cube, and small cubes of the column with one face on the top of large cube surface are all dark. Select the number of small white cubes of the large cube.