Clay layer A with single drainage and coefficient of consolidation Cv takes 6 months to achieve 50% consolidation. The time taken by clay layer B of the same thickness with double drainage and coefficient of consolidation $$\frac{{{\text{Cv}}}}{2}$$ to achieve the same degree of consolidation is

Clay layer A with single drainage and coefficient of consolidation Cv takes 6 months to achieve 50% consolidation. The time taken by clay layer B of the same thickness with double drainage and coefficient of consolidation $$\frac{{{\text{Cv}}}}{2}$$ to achieve the same degree of consolidation is Correct Answer 3 months

Bissoy MCQ

Related Questions

Let D be a simple graph on 10 vertices such that there is a vertex of degree 1, a vertex of degree 2, a vertex of degree 3, a vertex of degree 4, a vertex of degree 5, a vertex of degree 6, a vertex of degree 7, a vertex of degree 8 and a vertex of degree 9. What can be the degree of the last vertex?
In a public bathroom there are n taps 1,2,3...n. Tap1 and Tap2 take equal time to fill the tank while Tap3 takes half the time taken by Tap2 and Tap4 takes half the time taken by Tap3. Similarly each next number of tap takes half the time taken by previous number of Tap i.e, K-th Tap takes half the time taken by (K-1)th Tap.If the 10th tap takes 2 hours to fill the tank alone then what is the ratio of efficiency of 8th tap and 12th tap, respectively?
Hotel Aditya has 10 single AC rooms, 5 double AC rooms and 18 non AC rooms. The fixed monthly rent of hotel is 150,000. The per day maintenance cost is Rs. 100 for double AC room, Rs. 75 for single AC room and Rs. 40 for non AC room. The per day charges are Rs. 600 for double AC room, Rs. 400 for single AC room and Rs. 250 for non AC room. In April 2003, the occupancy rate of non AC room was 50%, 70% of single AC room and 40% of double AC rooms. Find the profit/loss % for that particular month.
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
A flat wall of fire clay, 50 cm thick and initially at 25 degree Celsius, has one of its faces suddenly exposed to a hot gas at 950 degree Celsius. If the heat transfer coefficient on the hot side is 7.5 W/m2 K and the other face of the wall is insulated so that no heat passes out of that face, determine the time necessary to raise the center of the wall to 350 degree Celsius. For fire clay brick Thermal conductivity = 1.12 W/m K Thermal diffusivity = 5.16 * 10 -7 m2/s
During heat treatment, cylindrical pieces of 25 mm diameter, 30 mm height and at 30 degree Celsius are placed in a furnace at 750 degree Celsius with convective coefficient 80 W/m2 degree. Calculate the time required to heat the pieces to 600 degree Celsius. Assume the following property values Density = 7850 kg /m3 Specific heat = 480 J/kg K Conductivity = 40 W/m degree
In a food processing plant, a brine solution is heated from – 12 degree Celsius to – 65 degree Celsius in a double pipe parallel flow heat exchanger by water entering at 35 degree Celsius and leaving at 20.5 degree Celsius. Let the rate of flow is 9 kg/min. Estimate the area of heat exchanger for an overall heat transfer coefficient of 860 W/m2 K. For water c P = 4.186 * 10 3 J/kg K
A composite slab consists of 5 cm thick layer of steel (k = 146 kJ/m hr degree) on the left side and a 6 cm thick layer of brass (k = 276 kJ/m hr degree) on the right hand side. The outer surfaces of the steel and brass are maintained at 100 degree Celsius and 50 degree Celsius. The contact between the two slabs is perfect and heat is generated at the rate of 4.2 * 10 5 k J/m2 hr at the plane of contact. The heat thus generated is dissipated from both sides of composite slab for steady state conditions. Calculate the temperature at the interface
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree