The Smaller the degree of deformation, the ____________ the required temperature to cause recrystallization.

The Smaller the degree of deformation, the ____________ the required temperature to cause recrystallization. Correct Answer higher

If the degree of deformation is smaller, the stored lattice strain energy will be lower. This will result in the lower driving force for recrystallization, and hence, higher temperature will be required.
Bissoy MCQ

Related Questions

Let D be a simple graph on 10 vertices such that there is a vertex of degree 1, a vertex of degree 2, a vertex of degree 3, a vertex of degree 4, a vertex of degree 5, a vertex of degree 6, a vertex of degree 7, a vertex of degree 8 and a vertex of degree 9. What can be the degree of the last vertex?
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
Whenever some external system of forces acts on a body, it undergoes some deformation. As the body undergoes some deformation, it sets up some resistance to the deformation. This resistance per unit area to deformation, is called
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
During heat treatment, cylindrical pieces of 25 mm diameter, 30 mm height and at 30 degree Celsius are placed in a furnace at 750 degree Celsius with convective coefficient 80 W/m2 degree. Calculate the time required to heat the pieces to 600 degree Celsius. Assume the following property values Density = 7850 kg /m3 Specific heat = 480 J/kg K Conductivity = 40 W/m degree
A two pass surface condenser is required to handle the exhaust from a turbine developing 15 MW with specific steam consumption of 5 kg/k W h. The quality of exhaust steam is 0.9, the condenser vacuum is 66 cm of mercury while the bar meter reads 76 cm of mercury. The condenser tubes are 28 mm inside diameter, 4 mm thick and water flows through tubes with a speed of 3 m/s and inlet temperature 20 degree Celsius. All the steam is condensed, the condensate is saturated water and temperature of cooling water at exit is 5 degree Celsius less than the condensate temperature. Assuming that overall coefficient of heat transfer is 4 k W/m2 degree, determine the mass of cooling water circulated
Inhomogeneous deformation of crystal results in regions of different orientation called deformation bands. Deformation bands have been observed in both fcc and bcc metals, but not in hcp metals.
A 25 mm diameter egg roll (k = 1 W/m degree) is roasted with the help of microwave heating. For good quality roasting, it is desired that temperature at the center of roll is maintained at 100 degree Celsius when the surrounding temperature is 25 degree Celsius. What should be the heating capacity in W/m 3 of the microwave if the heat transfer coefficient on the surface of egg roll is 20 W/m2 degree?
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip
A 2 cm thick steel slab heated to 525 degree Celsius is held in air stream having a mean temperature of 25 degree Celsius. Estimate the time interval when the slab temperature would not depart from the mean value of 25 degree Celsius by more than 0.5 degree Celsius at any point in the slab. The steel plate has the following thermal physical properties Density = 7950 kg/m3 C P = 455 J/kg K K = 46 W/m K