Bissoy.com
Doctors Medicines MCQs Q&A

If there is a decrease in viscosity, the heat transfer coefficient ____________

If there is a decrease in viscosity, the heat transfer coefficient ____________ Correct Answer Increase

If the viscosity decreases or density increases, it will offer less frictional resistance and cause quick draining of the condensate, thereby causing an increase in heat transfer coefficient.

Related Questions

Which one of the following sets is incorrect to show the inter-relationships among price elasticity coefficient, change in price and change in total revenue ? Price elasticity coefficient Change in price Change in Total Revenue 1) Zero Increase Decrease Increase Decrease (2) Less than 1 Increase Decrease Decrease Increase (3) Equal to 1 Increase Decrease No change No change (4) More than 1 Increase Decrease Decrease Increase  
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Experimental results indicate that the local heat transfer coefficient h g for flow over a flat plate with an extremely rough surface is approximated by the relation h x = a x -0.12 Where a is a constant coefficient and x is distance from the leading edge of the plate. What is the relation between this local heat transfer coefficient and the average heat transfer coefficient for a plate of length x?
The scales form in heat exchanges after a period of operation and provide additional resistance to heat transfer with some heat transfer coefficient . The reciprocal of this scale heat transfer coefficient is called .
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A heat exchanger to preheat oil for a furnace was designed without considering the possibility of scale formation, and the overall heat transfer coefficient based on the fuel oil side was 3200 k J/m2 hr degree. What would be the corrected coefficient of heat transfer if a fouling factor of 0.00025 m2 hr degree/k J for the fuel oil is taken into account?
The heat loss from unpainted aluminum side of a house has been calculated on the presumption that overall coefficient of heat transfer is 5 W/m 2 K. Later, it was discovered that the air pollution levels are such that fouling factor on this side is of the order of 0.0005 m2 K/W. Find overall heat transfer coefficient of dirty side
A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall