The Grimson’s correlation gives the set of parameters to be used to calculate the Nusselt number for the calculation of the heat transfer coefficient as Nu = C Ren Pr0.33.

The Grimson’s correlation gives the set of parameters to be used to calculate the Nusselt number for the calculation of the heat transfer coefficient as Nu = C Ren Pr0.33. Correct Answer True

Yes, the given statement is right because the set of parameters given by Grimson. Reynolds Number, Re Constant C Constant n 0.4 to 4 0.989 0.33 4 to 40 0.911 0.385 40 to 4000 0.683 0.466 40000 to 400000 0.0266 0.805
Bissoy MCQ

Related Questions

Which of the following statements relating to correlation and reegression are true?
1. The coefficient of correlation is independent of change of origin and scale
2. The coefficient of correlation between the two variables is the arithmetic average of the two regression coefficients
3. The probable error of the coefficient correlation is 0.6745 times of its standard error
4. Coefficient of correlation multiplied by the ratio between the standard deviations of the two variables denotes the slope of the regression line
Select the correct answer:
Which of the following statements are true?
1. The coefficient of rank correlation has the same limits as the Karl Pearson's coefficient of correlation.
2. The coefficient of correlation is independent of the change of origin but not of scale.
3. The covariance between $$X$$ and $$Y$$ is defined as $$\frac{{\sum {xy} }}{n}$$ where, $$x = \left( {X - \overline X } \right),y = \left( {Y - \overline Y } \right)$$      and $$n = $$ no. of paired observations.
4. $${b_{xy}}$$ is called regression coefficient of $$X$$ variable on $$Y$$ variable.
5. If $${b_{xy}}$$ is 0.4 and $${b_{yx}}$$ is 1.6, coefficient of determination would be 0.8.
Select the correct answer:
The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re0.8, where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter (D) as
Experimental results indicate that the local heat transfer coefficient h g for flow over a flat plate with an extremely rough surface is approximated by the relation h x = a x -0.12 Where a is a constant coefficient and x is distance from the leading edge of the plate. What is the relation between this local heat transfer coefficient and the average heat transfer coefficient for a plate of length x?
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
The calculation of heat transmission by convection is based on the determination of a Nusselt number or convective film coefficient. To that goal, which of the following strategies have been proposed (i) Non-dimensional analysis and experimental correlations (ii) Hydrodynamic concept of velocity boundary layer (iii) Reynolds similarity between the mechanism of fluid friction in the boundary layer and the transfer of heat by convection Identify the correct one
Consider we have a Double pipe Heat Exchanger, with inner tube of diameter 20mm (neglect thickness) and outer tube of diameter 30mm. We have two fluids A & B (KA = 15W/mK and KB = 20W/mK) we desire to have their flow rates as 15m3/s and 21m3/s respectively. If their Nusselt number after calculation is Nui = 429 and Nuo = 530. What is the overall heat transfer coefficient of the equipment is no fouling exists?
A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
The . . . . . . . . error of correlation is an amount which if added to and subtracted from the average correlation coefficient produces amounts within which the chances are even that a coefficient of correlation from a series error selected at random will fall.