Statement 1: Brookfield viscometer is an example of Coaxial Cylinder Viscometer. Statement 2: Working principle of a Brookfield viscometer: Two coaxial cylinders. Liquid is filled in between them. The viscosity produces torque which is directly proportional to the shear stress.

Statement 1: Brookfield viscometer is an example of Coaxial Cylinder Viscometer. Statement 2: Working principle of a Brookfield viscometer: Two coaxial cylinders. Liquid is filled in between them. The viscosity produces torque which is directly proportional to the shear stress. Correct Answer True, True

Both the statements pertaining to Brookfield viscometer are true.
Bissoy MCQ

Related Questions

Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Twp cylinders of equal size are filled with equal amount of ideal diatomic gas at room temperature. Both the cylinders are fitted with pistons. In cylinder A the piston is free to move, while in cylinder B the piston is fixed. When same amount of heat is added to cylinder A raises by 20 K. What will be the rise temperature of gas in cylinder B?
How is the degree of emulsion polymerization related to the monomer concentration, and the rate of radical generation, Ri? , inversely proportional to Ri b) inversely proportional to Ri, directly proportional to . c) directly proportional to Ri, independent of . d) directly proportional to , independent of Ri
Statement 1: Brookfield viscometer is very robust, is supported by software and even shows values of K and n, but, sometimes particles suspended in the fluid cause problems. Statement 2: Drawbacks of plate and cone viscometer: edge-effects, turbulence and temperature effects.
A large tank of height h is half-filled with a liquid of density ρ and other half-filled with a liquid of density 4ρ. A similar tank is half-filled with a liquid of density 2ρ and other-half filled with another liquid of density 3ρ as shown. What will be the ratio of the instantaneous velocities of discharge through a small opening at the base of the tanks? (assume that the diameter of the opening is negligible compared to the height of the liquid column in either of the tanks)
In Newton's law of viscosity, which states that the shear stress is proportional to the __________ co-efficient of viscosity is called dynamic or absolute viscosity (where, V = velocity, $${{\text{V}}_{\text{g}}}$$ = velocity gradient).
Statement 1: Considering the equation, μ_a= τ/γ = Kγ(n-1) , for pseudo plastic fluids, n<1 and they’re called Shear thinning liquids and dilatant fluids are called Shear thickening liquids as n>1. Statement 2: Cooked starch solution is a Shear thinning liquid and dairy cream is a Shear thickening liquid.
Shear stress versus shear rate behavior of four different types of fluids (I, II, III and IV) are shown in the figure below.
Basic Principles of Biotechnology mcq question image
Which one of the following options is correct?
If nominal shear stress $${\tau _{\text{v}}}$$ exceeds the design shear strength of concrete $${\tau _{\text{c}}}$$, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.