Air at 35 and 25 degree Celsius dew point temperature passes through the water shower whose temperature is maintained at 20 degree Celsius. What is the process involved?

Air at 35 and 25 degree Celsius dew point temperature passes through the water shower whose temperature is maintained at 20 degree Celsius. What is the process involved? Correct Answer Cooling and dehumidification

The process involved is cooling and dehumidification. Since the temperature of spray water is less than the dew point temperature cooling and dehumidification will take place.
Bissoy MCQ

Related Questions

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
Suppose saturated polar air has an air temperature and dew point of -10o C, and unsaturated desert air has an air temperature of 35o C and a dew point of 10o C. The desert air contains ______ water vapour and has a ________ relative humidity than the polar air.
Consider the following statements: 1. The relative humidity of air does not change with temperature as long as specific humidity remains constant. 2. Dew-point temperature is the temperature at which condensation begins when air is cooled at constant volume. 3. Saturated air passing over a water surface does not cause change of air temperature. 4. For saturated air, dry-bulb, wet-bulb and dew-point temperatures are identical. Which of the above statements are correct?
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
How far is point 'R' from Point 'T'? Statement (I): Point 'R' is 5 metres to the north of point 'M'. Point 'U' is 4 metres to the east of point 'R'. Point 'T' is to the west of point 'R' such that points 'U' 'R' and 'T' form a straight line of  metres. Statement (II): Point 'Z' is metres to the south of point 'T'. Point 'U' is  metres to the east of point 'T'. Point 'M' is  metres to the east of point 'Z'. Point 'R' is  metres to the north of point 'M'. Point 'R' lies on the line formed by joining points 'T' and 'U'.
A 2 cm thick steel slab heated to 525 degree Celsius is held in air stream having a mean temperature of 25 degree Celsius. Estimate the time interval when the slab temperature would not depart from the mean value of 25 degree Celsius by more than 0.5 degree Celsius at any point in the slab. The steel plate has the following thermal physical properties Density = 7950 kg/m3 C P = 455 J/kg K K = 46 W/m K
A counter flow heat exchanger is used to col 2000 kg/hr of oil (c p = 2.5 k J/kg K) from 105 degree Celsius to 30 degree Celsius by the use of water entering at 15 degree Celsius. If the overall heat transfer coefficient is expected to be 1.5 k W/m2 K, find out the water flow rate. Presume that the exit temperature of the water is not to exceed 80 degree Celsius
The lubricating oil for a large industrial gas turbine engine is cooled in a counter flow, concentric tube heat exchanger. The cooling water flows through the inner tube ( diameter = 25 mm) with inlet temperature 25 degree celsius and mass flow rate 0.2 kg/s. The oil flows through the annulus (diameter = 50 mm) with mass flow rate 0.125 kg/s and its temperature at entry and exit are 90 degree Celsius and 60 degree Celsius. Find outlet temperature of cooling water
Point A is 3m in the north of point B. Point D is 2m in the east of point E. Point F is 9m in the west of point G. Point C is 4m in the west of point B. Point C is 3m in the south of point D. Point F is 5m in the south of point E. Point H is 5m in the north of point G. What is the shortest distance between point H and point A?
A cylindrical stainless steel (k = 25 W/m K) ingot, 10 cm in diameter and 25 cm long, passes through a heat treatment furnace which is 5 meter in length. The initial ingot temperature is 90 degree Celsius, the furnace gas is at 1260 degree Celsius and the combined radiant and convective surface coefficient is 100 W/m2 K. Determine the maximum speed with which the ingot moves through the furnace if it must attain 830 degree Celsius temperature. Take thermal diffusivity as 0.45 * 10 -5 m2/s