Related Questions

A gear train consist of spur gear as shown. Gear A receives 4kW of power at 750rpm through its shaft and rotates in CW direction. A gear train consist of spur gear as shown. Gear A receives 4kW of power at 750rpm through its shaft and rotates in CW direction. Calculate the torque on the gear C if number of teeth on gear A, B and C are 40, 70 and 30.
Steps are given to draw involute of given circle. Arrange the steps f C is the centre of circle and P be the end of the thread (starting point). i. Draw a line PQ, tangent to the circle and equal to the circumference of the circle. ii. Draw the involute through the points P1, P2, P3 ……..etc. iii. Divide PQ and the circle into 12 equal parts. iv. Draw tangents at points 1, 2, 3 etc. and mark on them points P1, P2, P3 etc. such that 1P1 =P1l, 2P2 = P2l, 3P3= P3l etc.
A planetary gear train is shown in the figure. Number of teeth on the sun gear A, planet gear B and fixed ring gear D are given by 30, 70 and 140 respectively. Module is taken as 5mm. A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the gear ratio.
Following is the data for transmission system of a Gear box reduction ratios.
1st gear - 4.3 : 1
2nd gear - 3.00 : 1
3rd gear - 2.71 : 1
4th gear - 1 : 1
Final drive reduction is 5.0 : 1
The overall reduction when the vehicle is driven in 2nd gear is
Which two classes use the Shape class correctly?
A. public class Circle implements Shape { private int radius; }B. public abstract class Circle extends Shape { private int radius; }C. public class Circle extends Shape { private int radius; public void draw(); }D. public abstract class Circle implements Shape { private int radius; public void draw(); }E. public class Circle extends Shape { private int radius; public void draw() { /* code here */ } }F. public abstract class Circle implements Shape { private int radius; public void draw() { /* code here */ } }
Two involute gears are designed to mesh for a given centre distance and a given angular velocity ratio (other than 1). During assembly, the centre distance has increased slightly. Then which of the following changes occur? (i) Velocity ratio changes (ii) Pressure angle changes (iii) Pitch circle diameter changes (iv) Working depth changes (v) Base circle radius changes Select the correct answer using the code given below.
Which of the following statements are correct for mating gears with involute profiles? (i) The pressure angle, from the start of the engagement to the end of the engagement, remains constant. (ii) The pressure angle is maximum at the beginning of the engagement, reduces to zero at pitch point, starts decreasing and again becomes maximum at the end of the engagement. (iii) The face and flank of the teeth are generated by a single curve and the normal to this curve at any point is tangent to the base circle of the gear. (iv) The centre distance for a pair of mating gears can be varied within limits without altering the velocity ratio. Select the correct answer using the code given below.
A planetary gear train is shown in the figure. Number of teeth on the sun gear A, planet gear B and fixed ring gear D are given by 30, 70 and 140 respectively. Module is taken as 5mm. Calculate the tangential component of gear tooth force.
A gear train consist of spur gear as shown. Gear A receives 4kW of power at 750rpm through its shaft and rotates in CW direction. Calculate the tangential gear tooth force. Module of the gear is 5mm.
Steps given are to draw an involute of a given pentagon ABCDE. Arrange the steps. i. B as centre and radius AB, draw an arc cutting BC –extended at 1. ii. The curve thus obtained is the involute of the pentagon. iii. C as centre and radius C1, draw an arc cutting CD extended at 2. iv. Similarly, D, E, A as centres and radius D2, E3, A4, draw arcs cutting DE, EA, AB at 3, 4, 5 respectively.