Bissoy.com
Doctors Medicines MCQs Q&A

A rectangular beam of 500 mm wide is subjected to maximum shear force of 250kN, the corresponding maximum shear stress been 3 N/mm2. The depth of the beam is equal to ______

A rectangular beam of 500 mm wide is subjected to maximum shear force of 250kN, the corresponding maximum shear stress been 3 N/mm2. The depth of the beam is equal to ______ Correct Answer 250mm

The maximum shear force in a rectangular section is 3N/mm2. In rectangular sections; Maximum shear force = 3/2 × & 3 = 3/2 × d = 250mm.

Related Questions

Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
In which of the following cases, there exists the situation of Pure Bending in some part of the beam or along the entire beam? i) A simply supported beam subjected to two equally spaced downward concentrated loads ii) A simply supported beam subjected to two equally spaced opposite moments iii) A cantilever beam subjected to clockwise moment at free end iv) An overhanging beam with both side overhangs subjected to different concentrated loads at both the free ends
The following table shows the income (in rupees) for a particular month, together with their source, in respect of 5 employees (A, B, C, D and E).   A B C D E Salary 52,000 48,500 42,000 31,000 25,000 Overtime 0 0 1,500 2,500 3,200 Arrears 5.500 4,500 4,000 3,000 1,500 Bonus 3,500 3,000 2,500 2,000 2,000 Miscellaneous income 5,000 3,000 1,500 1,500 0 Total 66,000 59,000 40,000 40,000 31,700   For employee D, the income from overtime is what percentage of his total income?
A rectangular beam 100 mm wide is subjected to a maximum shear force and 50 kN. Find the depth of the beam.
The following table shows the income (In Rs.) for a particular month, together with their source, with respect to 5 employees (A, B, C, D, and E)   A B C D E Salary 52,000 48,500 42,000 31,000 25,000 Overtime 0 0 1,500 2,500 3,200 Arrears 5,500 4,500 4,000 3,000 1,500 Bonus 3,500 3,000 2,500 2,000 2,000 Miscellaneous income 5,000 3,000 2,000 1,500 0 Total 66,000 59,000 52,000 40,000 31,700   How many employees got more than a total of Rs. 10,000 as income other than salary?
The following table shows the income (in rupees) for a particular month, together with their source, in respect of 5 employees (A, B, C, D and E)   A B C D E Salary 52,000 48,500 42,000 31,000 25,000 Overtime 0 0 1,500 2,500 3,200 Arrears 5,500 4,500 4,000 3,000 1,500 Bonus 3,500 3,000 2,500 2,000 2,000 Miscellaneous income 5,000 3,000 2,000 1,500 0 Total 66,000 59,000 52,000 40,000 31,700 How many employees got more arrears than the average arrears received by all the employees?
The table below shows income (in rupees) for a particular month, together with their sources in respect of 5 employees A, B, C, D and E Employee A B C D E Salary 52,000 48,500 42,000 31,000 25,000 Overtime 0 0 1,500 2,500 3,200 Arrears 5,500 4,500 4,000 3,000 1,500 Bonus 3,500 3,000 2,500 2,000 2,000 Miscellaneous income 5,000 3,000 2,000 1,500 0 Total 66,000 59,000 52,000 40,000 31,700 How many employees have their salary more than four times their other incomes?
Consider the following statements with regards to the shear force diagram for the beam ABCD: 1. The beam ABCD is an overhanging beam having supports at A and D only. 2. The beam carries a point load of 20 kN at C. 3. The beam carries a concentrated load of 10 kN at the end B. 4. The beam is an overhanging beam having supports at C and D only. 5. The beam carries a uniformly distributed load of 70 kN over the left hand portion AC only. Which of the above statements are correct?
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum shear stress will be
When a beam of rectangular cross-section of width b and depth d, is subjected to a shear force F, the maximum shear stress induced will be