_________________ are intended for power drilling use only, the centre point locates the bit and the flat steel on either side cuts away the timber.

_________________ are intended for power drilling use only, the centre point locates the bit and the flat steel on either side cuts away the timber. Correct Answer Flat wood bits

Flat wood bits are used to drill fairly large holes and they give a flat bottom hole, so are ideal where the head of screw or bolt needs to be recessed into the timber. Always use these bits before drilling the clearance hole for the Bolt.
Bissoy MCQ

Related Questions

A steel plate d × b is sandwiched rigidly between two timber joists each D × B/2 in section. The moment of resistance of the beam for the same maximum permissible stress $$\sigma $$ in timber and steel will be (where Young's modulus of steel is m times that of the timber).
Given are the steps to draw a perpendicular to a line at a point within the line when the point is near the centre of line. Arrange the steps. Let AB be the line and P be the point in it i. Join F and P which is perpendicular to AB. ii. Now C as centre take the same radius and cut the arc at D and again D as centre with same radius cut the arc further at E. iii. With centre as P take any radius and draw an arc (more than a semicircle) cuts AB at C. iv. Now D, E as centre take radius (more than half of DE) draw arcs which cut at F.
Study the following information and answer the questions. Point A is 8m to the west of Point B. Point C is 4m to the south of Point B. Point D is 4m to the east of Point C. Point F is 6m to the north of Point D. Point E is 8m to the west of Point F. Point G is 2m to the south of Point E. How far and in which direction is Point G from Point A?
Study the following information and answer the questions. Point A is 8m to the west of Point B. Point C is 4m to the south of Point B. Point D is 4m to the east of Point C. Point F is 6m to the north of Point D. Point E is 8m to the west of Point F. Point G is 2m to the south of Point E. If point G is 4m to the north of Point H, then what is the distance between H and D?
The cutting speed for drilling aluminium, brass and bronze with carbon steel drills is _________ cutting speed for drilling mild steel with high speed steel drills.
Given are the steps to draw a perpendicular to a line at a point within the line when the point is near an end of the line. Arrange the steps. Let AB be the line and P be the point in it. i. Join the D and P. ii. With any point O draw an arc (more than a semicircle) with a radius of OP, cuts AB at C. iii. Join the C and O and extend till it cuts the large arc at D. iv. DP gives the perpendicular to AB.
A man starts from point 'O', travels 20 km towards east to reach point 'A', turns right and travels 10 km to reach point 'B', turns right and travels 9 km to reach point 'C', turns right and travels 5 km to reach point 'D', turns left and travels 12 km to reach point 'E' and then turns right and travels 6 km to reach point 'F'. What is the shortest distance between point 'E' and point 'C'?
A point is in 2nd quadrant, 15 units away from the vertical plane, 10 units away from the horizontal plane and 8 units away from the profile plane. Orthographic projection is drawn. What is the distance from point of front view to point of side view?
A point is in 4th quadrant, 15 dm away from the vertical plane, 10 dm away from the horizontal plane and 8 units away from the profile plane. Orthographic projection is drawn. What is the distance from point of front view to point of side view?
In the following questions are to be based on the details given below. A salesman visits 274 houses in a town to find out the views about three products X, Y and Z. He found that 157 use X, 98 use only X, 22 use all the three, 14 use X and Z but not Y, 39 use Y and Z, 48 use only Y. How many use product Z only?