Serial port connector-এ Pin সংখ্যা কতটি?

Serial port connector-এ Pin সংখ্যা কতটি? Correct Answer ৯

যে পোর্টের মাধ্যমে সিরিয়াল কমিউনিকেশন ডিভাইসকে সংযোগ দেয়া হয় তাকে সিরিয়াল কমিউনিকেশন পোর্ট বলা হয়। সিরিয়াল পোর্ট ২ সারিতে ৯টি পিন থাকে।
Bissoy MCQ

Related Questions

Question : On a T.V. channel, four serials A, B, C and D were screened, one on each day, on four consecutive days but not necessarily in that order. On which day was the serial C screened ?

Statements :
I. The first serial was screened on 23rd, Tuesday and was followed by serial D.
II. Serial A was not screened on 25th and one serial was screened between serials A and B.
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin. What will be the new radius of gyration?
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s2, then find the correction couple in N-m.
An 8-bit serial in/serial out shift register is used with a clock frequency of 150 kHz. What is the time delay between the serial input and the Q3 output?
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. Find the mass located at gudgeon pin in Kg.
A flange mounted shear pin is used on a shaft as a safety device. The steel shear pin has a diameter of 2.38 mm and is to be mounted on the flange of shaft rotating at 650 rpm. The maximum power transmitted by the shaft is 4.5 KW. If the shear strength of material of pin is 30 MPa, the radial distance of its mounting is ____
The two links OA and OB are connected by a pin joint at O. If the link OA turns with angular velocity $${\omega _1}$$ rad/s in the clockwise direction and the link OB turns with angular velocity $${\omega _2}$$ rad/s in the anticlockwise direction, then the rubbing velocity at the pin joint O is (where r = Radius of the pin at O)
The two links OA and OB are connected by a pin joint at O. If the link OA turns with angular velocity $${\omega _1}$$ rad/s in the clockwise direction and the link OB turns with angular velocity $${\omega _2}$$ rad/s in the clockwise direction, then the rubbing velocity at the pin joint O is (where r = Radius of the pin at O)
You are installing a network interface card on a computer with the following configuration: a 5867133 CPU, 16MB or RAM, a 800-MB IDE hard disk, a parallel port configured as LPT1, and a serial port configured as COM1, which is currently used by a mouse. In addition to the IDE host adapter and the video card, the following devices have been installed on the computer's expansion bus: a modem on COM2, a SCSI host adapter for a CD-ROM drive, and a sound card. The SCSI hose adapter is using IRQ 5, and the sound card is using IRQ 11. The network interface card that you are installing supports the following choices for IRQ: 2, 3, 4, 5, 9,10 and 11. Which IRQ(s) could you use for the network interface card without creating an IRQ conflict with another device?
The number of TTL inputs that can be sinked by the port 0 when a logic 0 is sent to a port line as an output port is