DHCP uses UDP port _________ for sending data to the server.

Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

A

Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl

B

On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol

C

On Engineering2 and Sales2, install and configure the DHCP Relay Agent service

D

Configure Engineering2 and Sales2 as DHCP servers without any scopes

E

None of above

You are the administrator of the Windows 2000 Server network shown in the exhibit. Users in the Research group and the Executive group have permission to access the Internet through a Windows 2000 Server computer running Microsoft Proxy Server. These users must enter their proxy server user names and passwords to connect to the proxy server, to the Internet, and to your local intranet server. The users who do not access the Internet do not have user accounts on the proxy server and, therefore, cannot connect to the intranet server. You want all users to be able to connect to the intranet server without entering a separate user name and password. What should you do?

A

Move the intranet server to the client segment of the network

B

Move the proxy server to the server segment of the network

C

Configure each client computer to bypass the proxy server for local addresses

D

Configure each client computer to use port 81 for the proxy server

E

None of above

Which of the following best describes the scopes on each DHCP server, in the absence of configuration problems with DHCP addresses, if you use multiple DHCP servers in your environment?

A

Unique to that subnet only

B

For different subnets

C

For no more than two subnets

D

For no subnets

E

None of the above

You are the administrator of a SQL Server 2000 computer. The server contains a database named FinanceData that is used by a client/server application. Each employee has a SQL Server login that the application uses to access the server.Your company hires a new employee named Andrew. You create a SQL Server login named Andrew. You also create a database user named Andrew in the database and grant the database user full permissions in the database.Whenever Andrew runs the client/server application, he receives the following error message: "Invalid object name." Andrew also reports that he cannot access the database by using the application.You need to ensure that Andrew can use the application. Which Transact-SQL statement should you execute?

A

EXEC sp_defaultdb 'Andrew','FinanceData'

B

GRANT ALL ON FinanceData TO Andrew

C

EXEC sp_addlogin 'Andrew'

D

EXEC sp_grantdbaccess 'FinanceData','Andrew'GOsp_addrolemember 'db_datareader','Andrew'

Which of the following describe the DHCP Discover message?
1. It uses FF:FF:FF:FF:FF:FF as a layer 2 broadcast.
2. It uses UDP as the Transport layer protocol.
3. It uses TCP as the Transport layer protocol.
4. It does not use a layer 2 destination address.

A

1 only

B

1 and 2

C

3 and 4

D

4 only

You configure your Windows 2000 Server as a print server. You install a second PnP Network adapter to improve the performance. The first adapter uses IRQ11, and the second adapter uses IRQ5. The server is now unable to print to print devices connected to a non-PnP LPT2 port adapter. You want to continue to use the print devices connected to your print server. What should you do?

A

Use device manager to change the IRQ for LPT1 to IRQ10

B

Use device manager to change the IRQ for LPT2 to IRQ7

C

Edit the CMOS setting of the servers BIOS to reserve IRQ7 for non-PnP devices

D

Edit the CMOS setting of the servers BIOS to reserve IRQ5 for non-PnP devices

E

None of above

You just finished installing the Dynamic Host Configuration Protocol (DHCP) service on a Windows 2000 Server computer that is a domain controller on your network. What must you do before the DHCP service can start?

A

Authorize the DHCP server in Active Directory

B

Configure a scope, a superscope, and a multicast scope

C

Configure a DHCP address reservation

D

Configure the DHCP server for DNS integration

You install a Windows 2000 Server computer on your network. You place several shared folders on a 12-GB primary partition formatted by FAT32. During nine months of continuous operation, the number of users who access the server and their access frequency remains constant. The average size of the files on the server remains approximately constant. After the server runs continuous for nine months, users report that the server does not retrieve files from the shared folders as fast as when you first installed the server. What should you do to resolve the problem?

A

Convert the disk that contains the shared folders to a dynamic disk

B

Convert the partition that contains the shared folders to NTFS

C

Defragment the disk that contains the shared folders

D

Move the paging file to the partition that contains the shared folders

E

None of above

You are the administrator of a SQL Server 2000 computer. Your company uses the server to store service contract information for its customers. You are also the administrator of an Oracle relational database management system (RDBMS) server. This server is used to store your company's financial information. The financial information is updated frequently throughout the day.You need to create a series of reports that combine the service contract information and the financial information. These reports will be updated several times a day.You want to create these reports on the SQL Server computer by using the minimum amount of disk space. What should you do?

A

Set up SQL Server replication to replicate the data from the Oracle server to the SQL Server computer.

B

Set up the Oracle server as a linked server. Create a view that joins the service contract information and the financial information.

C

Set up a Microsoft ActiveX script that connects to the Oracle server and imports the financial information into a SQL Server temporary table. Create a view that joins the service contract information and the temporary table.

D

Set up a Data Transformation Services (DTS) package that imports and transforms the data from the Oracle server to the SQL Server computer. Use SQL Server Agent to execute the DTS package throughout the day as needed.

You are a Web developer for XYZ. You create an ASP.NET application that accesses sales and marketing data. The data is stored in a Microsoft SQL Server 2000 database on a server named XYZ01.
The company purchases a factory automation software application. The application is installed on XYZ01, where it creates a second instance of SQL Server 2000 named Factory and a database named FactoryDB. You connect to FactoryDB by using Windows Integrated authentication.
You want to add a page to your ASP.NET application to display inventory data from FactoryDB. You use a SqlConnection object to connect to the database. You need to create a connection string to FactoryDB in the instance of SQL Server named Factory on XYZ01. Which string should you use?

A

?Server=XYZ01;Data Source=Factory; Initial Catalog=FactoryDB;Integrated Security=SSPI?

B

?Server=XYZ01;Data Source=Factory; Database=FactoryDB;Integrated Security=SSP1?

C

?Data Source=XYZ01\\Factory; Initial Category=Factory; Integrated Security=SSP1?

D

?Data Source=XYZ01\\Factory; Database=FactoryDB; Integrated Security=SSP1?

DHCP uses UDP port _________ for sending data to the server.

Related Questions