Bissoy.com
Doctors Medicines MCQs Q&A

In a computer program, the processor executing the same instructions over and over is called-

In a computer program, the processor executing the same instructions over and over is called- Correct Answer Looping

In computer science, a loop is a programming structure that repeats a sequence of instructions until a specific condition is met.

Related Questions

Consider three software items: Program-X, Control Flow Diagram of Program-Y and Control Flow Diagram of Program-Z as shown below Program-X: Control Flow Diagram of Program-Y sumcal (int maxint, int value) {       int result=0, i=0;       if (value <0)       {           Value = -value;       }       while ( (i
Assume that we test the performance of two processors, P1 and P2, on a program. We find the following about each: Processor P1 has a CPI of 2 and executes 2 billion instructions per second. Processor P2 has a CPI of 1 and executes 8 billion instructions per second. Which processor has higher performance on this program? (Recall that CPI stands for Cycles Per Instruction.)
The following are some events that occur after a device controller issues an interrupt while process L is under execution? (P) The processor pushes the process status onto the control stack. (Q) The processor finishes the execution of the current instruction. (R) The processor executes the interrupt service routine. (S) The processor pops the process status of from the control stack. (T) The processor loads the new PC value based on the interrupt. Which one of the following is the correct order in which the events above occur?
If the processor is executing the main program that calls a subroutine, then after executing the main program up to the CALL instruction, the control will be transferred to
At an Electronic Data processing unit, five out of the eight program sets P,Q,R,S,T,U,V and W are to be operated daily. On any one day, except for the first day of a month, only three of the program sets must be the ones that were operated on the previous day. The program operating must also satisfy the following conditions: 1. If program P is to be operated on a day, V can’t be operated on that day. 2. If Q is to be operated on a day, T must be one of the programs to be operated after Q. 3. If R is to be operated on a day, V must be one of the programs to be operated after R. 4. The last program to be operated on any day must be either S or U. If the program sets R and W are to be operated on the first day, which of the following could be the other program on that day?
In a computer program, the process of executing the same instructions over is called :
On a non-pipelined sequential processor, a program segment, which is a part of the interrupt service routine, is given to transfer 500 bytes from an I/O device to memory.     Initialize the address register     Initialize the count to 500 LOOP: Load a byte from device     Store in memory at address given by address register     Increment the address register     Decrement the count     If count! = 0 go to LOOP Assume that each statement in this program is equivalent to a machine instruction which takes one clock cycle to execute if it is a non-load/store instruction. The load-store instructions take two clock cycles to execute. The designer of the system also has an alternate approach of using the DMA controller to implement the same transfer. The DMA controller requires 20 clock cycles for initialization and other overheads. Each DMA transfer cycle takes two clock cycles to transfer one byte of data from the device to the memory. What is the approximate speedup when the DMA controller based design is used in place of the interrupt driven program based input-output?
Consider the following code sequence having five instructions I1 to I5. Each of these instructions has the following format. OP Ri, Rj, Rk Where operation OP is performed on contents of registers Rj and Rk and the result is stored in register Ri I1: ADD R1, R2, R3 I2: MUL R7, R1, R3 I3: SUB R4, R1, R5 I4: ADD R3, R2, R4 I5: MUL R7, R8, R9 Consider the following three statements. S1: There is an anti-dependence between instructions I2 and I5 S2: There is an anti-dependence between instructions I2 and I4 S3: Within an instruction pipeline an anti-dependence always creates one or more stalls Which one of the above statements is/are correct?
Consider a 32-bit processor which supports 70 instructions. Each instruction is 32 bit long and has 4 fields namely opcode, two register identifiers and an immediate operand of unsigned integer type. Maximum value of the immediate operand that can be supported by the processor is 8191. How many registers the processor has?
Which of the following are true? A. Desktop computer is a general-purpose computer made up of a separate monitor, keyboard, mouse and processor unit B. Laptop is where monitor, keyboard, pointing device, processor unit are combined in a single device C. Tablet is a device with a touch screen; which has a virtual keyboard which uses touch screen technology D. Smart Watch is a device that uses CRT technology so that the screen can bend around the wrist E. Mainframe computer runs small application where small data need to be processed Choose the correct answer from the options given below: