Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Consider the following statements: 1. The chain reaction process is used in nuclear bombs to release a vast amount of energy, but in nuclear reactors, there is no chain reaction. 2. In a nuclear reactor, the reaction is controlled, while in nuclear bombs, the reaction is uncontrolled. 3. In a nuclear reactor, all operating reactors are ‘critical’, while there is no question of ‘criticality’ in case of a nuclear bomb. 4. Nuclear reactors do not use moderators, while nuclear bombs use them. Which of the above statements about operational principles of a nuclear reactor and a nuclear bomb is / are correct?
Consider the following statements.
1. The chain reaction process is used in nuclear bombs to release a vast amount of energy, but in nuclear reactors, there is no chain reaction.
2. In a nuclear reactor, the reaction is controlled, while in nuclear bombs, the reaction is uncontrolled.
3. In a nuclear reactor, all operating reactors are 'critical', while there is no question of 'critically' in case of a nuclear bomb.
4. Nuclear reactors do not use moderators, while nuclear bombs use them.
Which of the above statements about operational principles of a nuclear reactor and a nuclear bomb is/are correct?
. . . . . . . . nuclear reactor does not require a heat exchanger to supply steam to power turbine.
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. The first full­scale, working steam ­powered tricycle was built by:
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. Cugnot built steam tractors for:
In a newly developed innovative idea brought up by CSIR in India, gas turbine exhaust gas are being utilized to convert feedwater into steam. Certain data of the experiment are as follows: mass flow rate of exhaust gas = 40 kg/hr, enthalpy of exhaust gas at the time of their exit from gas turbine is 600 kJ/kg, steam turbine output as measured by brake dynamometer = 60 hp-sec, thermal efficiency of steam power plant is 0.25, efficiency of exhaust gas in converting feedwater into steam is taken as 50%. Find the enthalpy of exhaust gas remaining after they generate steam from feedwater?
Which of the following statements about Printed circuit heat exchanger are correct? Statement 1: Printed circuit heat exchanger is an example for direct heat exchanger. Statement 2: It has high heat transfer surface area per unit volume of the exchanger.
Which of the following statement(s) is/are incorrect? (i) A turbine is called an impulse turbine if at the inlet of the turbine total energy is only kinetic energy (ii) A turbine is called a reaction turbine if at the inlet of the turbine the total energy is kinetic energy and pressure energy (iii) The inward flow reaction turbine having radial discharge at the outlet is known as Kaplan turbine